70 lines
2.1 KiB
C
70 lines
2.1 KiB
C
#ifndef _PRST_CONFIG_H_
|
|
#define _PRST_CONFIG_H_
|
|
|
|
#include "nrf_gpio.h"
|
|
|
|
// Some configurations are version-specific. Uncomment the line corresponding
|
|
// the the version you're programming. The version can be found on the
|
|
// b-parasite board.
|
|
// #define PRST_VERSION_1_0_X
|
|
#define PRST_VERSION_1_1_X
|
|
|
|
// Built-in LED.
|
|
#define PRST_LED_PIN NRF_GPIO_PIN_MAP(0, 28)
|
|
|
|
// Deep sleep.
|
|
#define PRST_DEEP_SLEEP_IN_SECONDS 300
|
|
|
|
// Analog to digital converter (ADC).
|
|
// Prints out ADC debug info, such as the values read for battery and soil
|
|
// moisture.
|
|
#define PRST_ADC_BATT_DEBUG 0
|
|
#define PRST_ADC_SOIL_DEBUG 0
|
|
|
|
// BLE.
|
|
// Prints out BLE debug info, such as the final encoded advertisement packet.
|
|
#define PRST_BLE_DEBUG 0
|
|
#define PRST_BLE_PROTOCOL_VERSION 1
|
|
// We're using a random static MAC address, which has the following constraints:
|
|
// 1. Two most significant bits are set to 1;
|
|
// 2. The remaining bits should not _all_ be set to 0;
|
|
// 2. The remaining bits should not _all_ be set to 1;
|
|
#define PRST_BLE_MAC_ADDR "f0:ca:f0:ca:01:01"
|
|
#define PRST_BLE_ADV_NAME "prst"
|
|
// Total time spend advertising.
|
|
#define PRST_BLE_ADV_TIME_IN_MS 1000
|
|
// Interval between advertising packets.
|
|
// From the specs, this value has to be greater or equal 20ms.
|
|
#define PRST_BLE_ADV_INTERVAL_IN_MS 30
|
|
// Possible values are ..., -8, -4, 0, 4, 8.
|
|
#define PRST_BLE_ADV_TX_POWER 8
|
|
|
|
// PWM.
|
|
#define PRST_PWM_PIN NRF_GPIO_PIN_MAP(0, 5)
|
|
|
|
#ifdef NRF52833_XXAA
|
|
#define PRST_FAST_DISCH_PIN NRF_GPIO_PIN_MAP(0, 25)
|
|
#else
|
|
#define PRST_FAST_DISCH_PIN NRF_GPIO_PIN_MAP(1, 10)
|
|
#endif
|
|
|
|
// SHT3C temp/humidity sensor.
|
|
#define PRST_SHT3C_DEBUG 0
|
|
|
|
// Version-specific configuration.
|
|
#if defined(PRST_VERSION_1_1_X)
|
|
// The photoresistor (LDR) is optional in this revision. If set to 1, the LDR's
|
|
// ADC channel will be sampled and its data will be encoded in the BLE
|
|
// advertisement packet.
|
|
#define PRST_HAS_LDR 1
|
|
|
|
// Light sensor pins.
|
|
#define PRST_PHOTO_V_PIN NRF_GPIO_PIN_MAP(0, 29)
|
|
#define PRST_PHOTO_OUT_PIN NRF_GPIO_PIN_MAP(0, 2)
|
|
|
|
// Whether to produce debug messages for the LDR
|
|
#define PRST_ADC_PHOTO_DEBUG 0
|
|
|
|
#endif // End of version-specific configuration.
|
|
|
|
#endif // _PRST_CONFIG_H_
|