a7732f106b
This flags makes use of the Coded PHY from Bluetooth 5. It should be treated as an experimental feature and it's disabled by default. Note that clients (such as ESPHomme) would also have to scan on the Coded PHY to be able to find b-parasites operating in this mode. Currently, no client does that. Thus the feature is disabled and marked as experimental.
96 lines
3.1 KiB
C
96 lines
3.1 KiB
C
#ifndef _PRST_CONFIG_H_
|
|
#define _PRST_CONFIG_H_
|
|
|
|
#include "nrf_gpio.h"
|
|
// Some configurations are version-specific. Uncomment the line corresponding
|
|
// the the version you're programming. The version can be found on the
|
|
// b-parasite board.
|
|
// #define PRST_VERSION_1_0_X
|
|
// #define PRST_VERSION_1_1_X
|
|
#define PRST_VERSION_1_2_X
|
|
|
|
// Built-in LED.
|
|
// Wether or not to turn the LED on/off during the wake-up cycle. Impacts
|
|
// battery life.
|
|
#define PRST_BLINK_LED 0
|
|
#define PRST_LED_PIN NRF_GPIO_PIN_MAP(0, 28)
|
|
|
|
// Deep sleep.
|
|
#define PRST_DEEP_SLEEP_IN_SECONDS 300
|
|
|
|
// Analog to digital converter (ADC).
|
|
// Prints out ADC debug info, such as the values read for battery and soil
|
|
// moisture.
|
|
#define PRST_ADC_BATT_DEBUG 0
|
|
#define PRST_ADC_SOIL_DEBUG 0
|
|
|
|
// BLE.
|
|
// Prints out BLE debug info, such as the final encoded advertisement packet.
|
|
#define PRST_BLE_DEBUG 0
|
|
// The BLE protocol version defines how the sensors' data is encoded inside the
|
|
// BLE advertisement packet. Possible values are 1 and 2.
|
|
#define PRST_BLE_PROTOCOL_VERSION 1
|
|
|
|
// There are two options for configuring the MAC address of b-parasites:
|
|
// 1. Comment out the PRST_BLE_MAC_ADDR to use a random static MAC address that
|
|
// is preprogrammed in each nRF52 chip.
|
|
// 2. Manually specify the MAC address you want below. In this scenario, the
|
|
// following constraints must be met to ensure valid random static MAC
|
|
// addresses:
|
|
// a. Two most significant bits are set to 1;
|
|
// b. The remaining bits should not _all_ be set to 0;
|
|
// c. The remaining bits should not _all_ be set to 1;
|
|
#define PRST_BLE_MAC_ADDR "f0:ca:f0:ca:01:01"
|
|
|
|
#define PRST_BLE_ADV_NAME "prst"
|
|
// Total time spend advertising.
|
|
#define PRST_BLE_ADV_TIME_IN_MS 1000
|
|
// Interval between advertising packets.
|
|
// From the specs, this value has to be greater or equal 20ms.
|
|
#define PRST_BLE_ADV_INTERVAL_IN_MS 30
|
|
// Possible values are ..., -8, -4, 0, 4, 8.
|
|
#define PRST_BLE_ADV_TX_POWER 8
|
|
// Experimental support for "long range" BLE, introduced in Bluetooth 5. It uses
|
|
// a different type of physical layer - the Coded PHY. Receivers should also
|
|
// scan using Coded PHY in order to find this device when operating in this
|
|
// mode.
|
|
#define PRST_BLE_EXPERIMENTAL_LONG_RANGE 0
|
|
|
|
// PWM.
|
|
#define PRST_PWM_PIN NRF_GPIO_PIN_MAP(0, 5)
|
|
|
|
#ifdef NRF52833_XXAA
|
|
#define PRST_FAST_DISCH_PIN NRF_GPIO_PIN_MAP(0, 25)
|
|
#else
|
|
#define PRST_FAST_DISCH_PIN NRF_GPIO_PIN_MAP(1, 10)
|
|
#endif
|
|
|
|
// SHT3C temp/humidity sensor.
|
|
#define PRST_SHT3C_DEBUG 0
|
|
|
|
// Version-specific configuration.
|
|
#if defined(PRST_VERSION_1_1_X)
|
|
// The photoresistor (LDR) is optional in this revision. If set to 1, the LDR's
|
|
// ADC channel will be sampled and its data will be encoded in the BLE
|
|
// advertisement packet.
|
|
#define PRST_HAS_LDR 1
|
|
|
|
// Light sensor pins.
|
|
#define PRST_PHOTO_V_PIN NRF_GPIO_PIN_MAP(0, 29)
|
|
#define PRST_PHOTO_OUT_PIN NRF_GPIO_PIN_MAP(0, 2)
|
|
|
|
// Whether to produce debug messages for the LDR
|
|
#define PRST_ADC_PHOTO_DEBUG 0
|
|
|
|
#elif defined(PRST_VERSION_1_2_X)
|
|
|
|
#define PRST_HAS_PHOTOTRANSISTOR 1
|
|
|
|
#define PRST_PHOTO_V_PIN NRF_GPIO_PIN_MAP(0, 29)
|
|
#define PRST_PHOTO_OUT_PIN NRF_GPIO_PIN_MAP(0, 2)
|
|
|
|
#define PRST_ADC_PHOTO_DEBUG 0
|
|
|
|
#endif // End of version-specific configuration.
|
|
|
|
#endif // _PRST_CONFIG_H_
|